Merge git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux

Merge mainline to pick up c7513c2 ("crypto/arm64: aes-ce-gcm -
add missing kernel_neon_begin/end pair").

Documentation/admin-guide/kernel-parameters.txt

@@ -4846,3 +4846,8 @@
 	xirc2ps_cs=	[NET,PCMCIA]
 			Format:
 			<irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
+
+	xhci-hcd.quirks		[USB,KNL]
+			A hex value specifying bitmask with supplemental xhci
+			host controller quirks. Meaning of each bit can be
+			consulted in header drivers/usb/host/xhci.h.

Documentation/admin-guide/pm/intel_pstate.rst

@@ -324,8 +324,7 @@ Global Attributes
 
 ``intel_pstate`` exposes several global attributes (files) in ``sysfs`` to
 control its functionality at the system level.  They are located in the
-``/sys/devices/system/cpu/cpufreq/intel_pstate/`` directory and affect all
-CPUs.
+``/sys/devices/system/cpu/intel_pstate/`` directory and affect all CPUs.
 
 Some of them are not present if the ``intel_pstate=per_cpu_perf_limits``
 argument is passed to the kernel in the command line.
@@ -379,6 +378,17 @@ argument is passed to the kernel in the command line.
 	but it affects the maximum possible value of per-policy P-state	limits
 	(see `Interpretation of Policy Attributes`_ below for details).
 
+``hwp_dynamic_boost``
+	This attribute is only present if ``intel_pstate`` works in the
+	`active mode with the HWP feature enabled <Active Mode With HWP_>`_ in
+	the processor.  If set (equal to 1), it causes the minimum P-state limit
+	to be increased dynamically for a short time whenever a task previously
+	waiting on I/O is selected to run on a given logical CPU (the purpose
+	of this mechanism is to improve performance).
+
+	This setting has no effect on logical CPUs whose minimum P-state limit
+	is directly set to the highest non-turbo P-state or above it.
+
 .. _status_attr:
 
 ``status``
@@ -410,7 +420,7 @@ argument is passed to the kernel in the command line.
 	That only is supported in some configurations, though (for example, if
 	the `HWP feature is enabled in the processor <Active Mode With HWP_>`_,
 	the operation mode of the driver cannot be changed), and if it is not
-	supported in the current configuration, writes to this attribute with
+	supported in the current configuration, writes to this attribute will
 	fail with an appropriate error.
 
 Interpretation of Policy Attributes

Documentation/core-api/kernel-api.rst

@@ -284,7 +284,7 @@ Resources Management
 MTRR Handling
 -------------
 
-.. kernel-doc:: arch/x86/kernel/cpu/mtrr/main.c
+.. kernel-doc:: arch/x86/kernel/cpu/mtrr/mtrr.c
    :export:
 
 Security Framework

Documentation/device-mapper/writecache.txt

@@ -15,6 +15,8 @@ Constructor parameters:
    size)
 5. the number of optional parameters (the parameters with an argument
    count as two)
+	start_sector n		(default: 0)
+		offset from the start of cache device in 512-byte sectors
 	high_watermark n	(default: 50)
 		start writeback when the number of used blocks reach this
 		watermark

Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt

@@ -66,7 +66,7 @@ Required root node properties:
 	- "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale
 				    Octa board.
 	- "insignal,origen"       - for Exynos4210-based Insignal Origen board.
-	- "insignal,origen4412    - for Exynos4412-based Insignal Origen board.
+	- "insignal,origen4412"   - for Exynos4412-based Insignal Origen board.
 
 
 Optional nodes:

Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt

@@ -36,7 +36,7 @@ Optional nodes:
 
  - port/ports: to describe a connection to an external encoder. The
    binding follows Documentation/devicetree/bindings/graph.txt and
-   suppors a single port with a single endpoint.
+   supports a single port with a single endpoint.
 
  - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and
    Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting

Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt

@@ -1,7 +1,7 @@
 Nintendo Wii (Hollywood) GPIO controller
 
 Required properties:
-- compatible: "nintendo,hollywood-gpio
+- compatible: "nintendo,hollywood-gpio"
 - reg: Physical base address and length of the controller's registers.
 - gpio-controller: Marks the device node as a GPIO controller.
 - #gpio-cells: Should be <2>. The first cell is the pin number and the

Documentation/devicetree/bindings/input/sprd,sc27xx-vibra.txt

@@ -0,0 +1,23 @@
+Spreadtrum SC27xx PMIC Vibrator
+
+Required properties:
+- compatible: should be "sprd,sc2731-vibrator".
+- reg: address of vibrator control register.
+
+Example :
+
+	sc2731_pmic: pmic@0 {
+		compatible = "sprd,sc2731";
+		reg = <0>;
+		spi-max-frequency = <26000000>;
+		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vibrator@eb4 {
+			compatible = "sprd,sc2731-vibrator";
+			reg = <0xeb4>;
+		};
+	};

Documentation/devicetree/bindings/input/touchscreen/hideep.txt

@@ -32,7 +32,7 @@ i2c@00000000 {
 		reg = <0x6c>;
 		interrupt-parent = <&gpx1>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
-		vdd-supply = <&ldo15_reg>";
+		vdd-supply = <&ldo15_reg>;
 		vid-supply = <&ldo18_reg>;
 		reset-gpios = <&gpx1 5 0>;
 		touchscreen-size-x = <1080>;

Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt

@@ -15,7 +15,7 @@ Required properties:
   include "nvidia,tegra30-ictlr".	
 - reg : Specifies base physical address and size of the registers.
   Each controller must be described separately (Tegra20 has 4 of them,
-  whereas Tegra30 and later have 5"  
+  whereas Tegra30 and later have 5).
 - interrupt-controller : Identifies the node as an interrupt controller.
 - #interrupt-cells : Specifies the number of cells needed to encode an
   interrupt source. The value must be 3.

Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt

@@ -12,7 +12,7 @@ Required properties:
   specifier, shall be 2
 - interrupts: interrupts references to primary interrupt controller
   (only needed for exti controller with multiple exti under
-  same parent interrupt: st,stm32-exti and st,stm32h7-exti")
+  same parent interrupt: st,stm32-exti and st,stm32h7-exti)
 
 Example:
 

Documentation/devicetree/bindings/mips/brcm/soc.txt

@@ -152,7 +152,7 @@ Required properties:
 - compatible	: should contain one of:
 		  "brcm,bcm7425-timers"
 		  "brcm,bcm7429-timers"
-		  "brcm,bcm7435-timers and
+		  "brcm,bcm7435-timers" and
 		  "brcm,brcmstb-timers"
 - reg		: the timers register range
 - interrupts	: the interrupt line for this timer block

Documentation/devicetree/bindings/net/fsl-fman.txt

@@ -238,7 +238,7 @@ PROPERTIES
 		Must include one of the following:
 		- "fsl,fman-dtsec" for dTSEC MAC
 		- "fsl,fman-xgec" for XGEC MAC
-		- "fsl,fman-memac for mEMAC MAC
+		- "fsl,fman-memac" for mEMAC MAC
 
 - cell-index
 		Usage: required

Documentation/devicetree/bindings/power/power_domain.txt

@@ -133,7 +133,7 @@ located inside a PM domain with index 0 of a power controller represented by a
 node with the label "power".
 In the second example the consumer device are partitioned across two PM domains,
 the first with index 0 and the second with index 1, of a power controller that
-is represented by a node with the label "power.
+is represented by a node with the label "power".
 
 Optional properties:
 - required-opps: This contains phandle to an OPP node in another device's OPP

Documentation/devicetree/bindings/regulator/tps65090.txt

@@ -16,7 +16,7 @@ Required properties:
 Optional properties:
 - ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
   If DCDCs are externally controlled then this property should be there.
-- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
+- dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
   If DCDCs are externally controlled and if it is from GPIO then GPIO
   number should be provided. If it is externally controlled and no GPIO
   entry then driver will just configure this rails as external control

Documentation/devicetree/bindings/reset/st,sti-softreset.txt

@@ -15,7 +15,7 @@ Please refer to reset.txt in this directory for common reset
 controller binding usage.
 
 Required properties:
-- compatible: Should be st,stih407-softreset";
+- compatible: Should be "st,stih407-softreset";
 - #reset-cells: 1, see below
 
 example:

Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt

@@ -39,7 +39,7 @@ Required properties:
 
 Optional property:
 - clock-frequency:	Desired I2C bus clock frequency in Hz.
-			When missing default to 400000Hz.
+			When missing default to 100000Hz.
 
 Child nodes should conform to I2C bus binding as described in i2c.txt.
 

Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt

@@ -30,7 +30,7 @@ Required properties:
 
 			  Board connectors:
 			  * Headset Mic
-			  * Secondary Mic",
+			  * Secondary Mic
 			  * DMIC
 			  * Ext Spk
 

Documentation/devicetree/bindings/sound/qcom,apq8096.txt

@@ -35,7 +35,7 @@ This binding describes the APQ8096 sound card, which uses qdsp for audio.
 			"Digital Mic3"
 
 		Audio pins and MicBias on WCD9335 Codec:
-			"MIC_BIAS1
+			"MIC_BIAS1"
 			"MIC_BIAS2"
 			"MIC_BIAS3"
 			"MIC_BIAS4"

Documentation/devicetree/bindings/usb/rockchip,dwc3.txt

@@ -16,7 +16,8 @@ A child node must exist to represent the core DWC3 IP block. The name of
 the node is not important. The content of the node is defined in dwc3.txt.
 
 Phy documentation is provided in the following places:
-Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
+Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt - USB2.0 PHY
+Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt     - Type-C PHY
 
 Example device nodes:
 

Documentation/devicetree/bindings/w1/w1-gpio.txt

@@ -15,7 +15,7 @@ Optional properties:
 
 Examples:
 
-	onewire@0 {
+	onewire {
 		compatible = "w1-gpio";
 		gpios = <&gpio 126 0>, <&gpio 105 0>;
 	};

Documentation/driver-api/infrastructure.rst

@@ -49,10 +49,10 @@ Device Drivers Base
 Device Drivers DMA Management
 -----------------------------
 
-.. kernel-doc:: drivers/base/dma-coherent.c
+.. kernel-doc:: kernel/dma/coherent.c
    :export:
 
-.. kernel-doc:: drivers/base/dma-mapping.c
+.. kernel-doc:: kernel/dma/mapping.c
    :export:
 
 Device drivers PnP support

Documentation/filesystems/Locking

@@ -441,8 +441,6 @@ prototypes:
 	int (*iterate) (struct file *, struct dir_context *);
 	int (*iterate_shared) (struct file *, struct dir_context *);
 	__poll_t (*poll) (struct file *, struct poll_table_struct *);
-	struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
-	__poll_t (*poll_mask) (struct file *, __poll_t);
 	long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
 	long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
 	int (*mmap) (struct file *, struct vm_area_struct *);
@@ -473,7 +471,7 @@ prototypes:
 };
 
 locking rules:
-	All except for ->poll_mask may block.
+	All may block.
 
 ->llseek() locking has moved from llseek to the individual llseek
 implementations.  If your fs is not using generic_file_llseek, you
@@ -505,9 +503,6 @@ in sys_read() and friends.
 the lease within the individual filesystem to record the result of the
 operation
 
-->poll_mask can be called with or without the waitqueue lock for the waitqueue
-returned from ->get_poll_head.
-
 --------------------------- dquot_operations -------------------------------
 prototypes:
 	int (*write_dquot) (struct dquot *);

Documentation/filesystems/cifs/AUTHORS

@@ -42,9 +42,11 @@ Jeff Layton (many, many fixes, as well as great work on the cifs Kerberos code)
 Scott Lovenberg
 Pavel Shilovsky (for great work adding SMB2 support, and various SMB3 features)
 Aurelien Aptel (for DFS SMB3 work and some key bug fixes)
-Ronnie Sahlberg (for SMB3 xattr work and bug fixes)
+Ronnie Sahlberg (for SMB3 xattr work, bug fixes, and lots of great work on compounding)
 Shirish Pargaonkar (for many ACL patches over the years)
 Sachin Prabhu (many bug fixes, including for reconnect, copy offload and security)
+Paulo Alcantara
+Long Li (some great work on RDMA, SMB Direct)
 
 
 Test case and Bug Report contributors
@@ -58,5 +60,4 @@ mention to the Stanford Checker (SWAT) which pointed out many minor
 bugs in error paths.  Valuable suggestions also have come from Al Viro
 and Dave Miller.
 
-And thanks to the IBM LTC and Power test teams and SuSE testers for
-finding multiple bugs during excellent stress test runs.
+And thanks to the IBM LTC and Power test teams and SuSE and Citrix and RedHat testers for finding multiple bugs during excellent stress test runs.

Documentation/filesystems/cifs/CHANGES

@@ -1,3 +1,6 @@
+See https://wiki.samba.org/index.php/LinuxCIFSKernel for
+more current information.
+
 Version 1.62
 ------------
 Add sockopt=TCP_NODELAY mount option. EA (xattr) routines hardened

Documentation/filesystems/cifs/TODO

@@ -9,14 +9,14 @@ is a partial list of the known problems and missing features:
 
 a) SMB3 (and SMB3.02) missing optional features:
    - multichannel (started), integration with RDMA
-   - directory leases (improved metadata caching)
-   - T10 copy offload (copy chunk, and "Duplicate Extents" ioctl
+   - directory leases (improved metadata caching), started (root dir only)
+   - T10 copy offload ie "ODX" (copy chunk, and "Duplicate Extents" ioctl
      currently the only two server side copy mechanisms supported)
 
 b) improved sparse file support
 
 c) Directory entry caching relies on a 1 second timer, rather than
-using Directory Leases
+using Directory Leases, currently only the root file handle is cached longer
 
 d) quota support (needs minor kernel change since quota calls
 to make it to network filesystems or deviceless filesystems)
@@ -42,6 +42,8 @@ mount or a per server basis to client UIDs or nobody if no mapping
 exists. Also better integration with winbind for resolving SID owners
 
 k) Add tools to take advantage of more smb3 specific ioctls and features
+(passthrough ioctl/fsctl for sending various SMB3 fsctls to the server
+is in progress)
 
 l) encrypted file support
 
@@ -71,9 +73,8 @@ t) split cifs and smb3 support into separate modules so legacy (and less
 secure) CIFS dialect can be disabled in environments that don't need it
 and simplify the code.
 
-u) Finish up SMB3.1.1 dialect support
-
-v) POSIX Extensions for SMB3.1.1
+v) POSIX Extensions for SMB3.1.1 (started, create and mkdir support added
+so far).
 
 KNOWN BUGS
 ====================================
@@ -92,8 +93,8 @@ Misc testing to do
 1) check out max path names and max path name components against various server
 types. Try nested symlinks (8 deep). Return max path name in stat -f information
 
-2) Improve xfstest's cifs enablement and adapt xfstests where needed to test
-cifs better
+2) Improve xfstest's cifs/smb3 enablement and adapt xfstests where needed to test
+cifs/smb3 better
 
 3) Additional performance testing and optimization using iozone and similar - 
 there are some easy changes that can be done to parallelize sequential writes,

Documentation/filesystems/vfs.txt

@@ -857,8 +857,6 @@ struct file_operations {
 	ssize_t (*write_iter) (struct kiocb *, struct iov_iter *);
 	int (*iterate) (struct file *, struct dir_context *);
 	__poll_t (*poll) (struct file *, struct poll_table_struct *);
-	struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
-	__poll_t (*poll_mask) (struct file *, __poll_t);
 	long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
 	long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
 	int (*mmap) (struct file *, struct vm_area_struct *);
@@ -903,17 +901,6 @@ otherwise noted.
 	activity on this file and (optionally) go to sleep until there
 	is activity. Called by the select(2) and poll(2) system calls
 
-  get_poll_head: Returns the struct wait_queue_head that callers can
-  wait on.  Callers need to check the returned events using ->poll_mask
-  once woken.  Can return NULL to indicate polling is not supported,
-  or any error code using the ERR_PTR convention to indicate that a
-  grave error occured and ->poll_mask shall not be called.
-
-  poll_mask: return the mask of EPOLL* values describing the file descriptor
-  state.  Called either before going to sleep on the waitqueue returned by
-  get_poll_head, or after it has been woken.  If ->get_poll_head and
-  ->poll_mask are implemented ->poll does not need to be implement.
-
   unlocked_ioctl: called by the ioctl(2) system call.
 
   compat_ioctl: called by the ioctl(2) system call when 32 bit system calls