forked from whosawhatsis/Deezmaker-slicing-profiles
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathCura Bukobot Duo PLA+TPE (very experimental).ini
160 lines (158 loc) · 5.33 KB
/
Cura Bukobot Duo PLA+TPE (very experimental).ini
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
[profile]
layer_height = 0.15
wall_thickness = 1.0
retraction_enable = True
solid_layer_thickness = 1.5
fill_density = 20
nozzle_size = 0.4
print_speed = 40
print_temperature = 210
print_temperature2 = 240
print_temperature3 = 0
print_temperature4 = 0
print_bed_temperature = 0
support = None
platform_adhesion = None
support_dual_extrusion = Both
wipe_tower = True
wipe_tower_volume = 30
ooze_shield = True
filament_diameter = 2.85
filament_diameter2 = 2.75
filament_diameter3 = 0
filament_diameter4 = 0
filament_flow = 100.0
retraction_speed = 10
retraction_amount = 1.2
retraction_dual_amount = 5
retraction_min_travel = .5
retraction_combing = True
retraction_minimal_extrusion = 0.02
retraction_hop = 0.0
bottom_thickness = 0.2
object_sink = 0.0
overlap_dual = 0.15
travel_speed = 600.0
bottom_layer_speed = 10
infill_speed = 0.0
inset0_speed = 0.0
insetx_speed = 0.0
cool_min_layer_time = 10
fan_enabled = True
skirt_line_count = 1
skirt_gap = 1
skirt_minimal_length = 0.0
fan_full_height = 0.5
fan_speed = 100
fan_speed_max = 100
cool_min_feedrate = 10
cool_head_lift = False
solid_top = True
solid_bottom = True
fill_overlap = 15
support_type = Grid
support_angle = 60
support_fill_rate = 15
support_xy_distance = 0.7
support_z_distance = 0.15
spiralize = False
brim_line_count = 10
raft_margin = 5
raft_line_spacing = 1.0
raft_base_thickness = 0.3
raft_base_linewidth = 0.7
raft_interface_thickness = 0.2
raft_interface_linewidth = 0.2
fix_horrible_union_all_type_a = True
fix_horrible_union_all_type_b = False
fix_horrible_use_open_bits = False
fix_horrible_extensive_stitching = False
plugin_config = (lp1
.
object_center_x = -1
object_center_y = -1
[alterations]
start.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
;M109 S{print_temperature} ;Uncomment to add your own temperature line
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
T0
;M200 D2.75 ; set filament diameter and switch to volumetric extrusion (mm^3)
T1
;M200 D2.85; set filament diameter and switch to volumetric extrusion (mm^3)
T0
M207 S2 F1800 ; configure firmware retraction
M208 S0 F120 ; configure firmware retraction recover
M209 S1 ; autoretract on
G28 ; home all axes
G1 Z15.0 F{travel_speed} ;move the platform down 15mm
G92 E-5 ;reset E position for priming
G1 F200 E0 ; prime extruder
G1 F{travel_speed}
;Put printing message on LCD screen
end.gcode =
M104 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
M221 S100
M200 D0 ; switch back to extrude by filament length (mm)
M104 S0 ; turn off temperature
M140 S0 ; turn off temperature
G28 X0 ; home X axis
G92 E25 ; set filament length for retraction
G1 E0 F1800; retract filament to prevent it from seizing in the cooled nozzle
M84 ; disable motors
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
;M104 S{print_temperature} ;Uncomment to add your own temperature line
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
G21 ;metric values
G90 ;absolute positioning
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F{travel_speed} ;move the platform down 15mm
T1 ;Switch to the 2nd extruder
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F200 E-{retraction_dual_amount}
T0 ;Switch to the first extruder
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F{travel_speed}
end2.gcode = ;End GCode
M104 T0 S0 ;extruder heater off
M104 T1 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
support_start.gcode =
support_end.gcode =
cool_start.gcode =
cool_end.gcode =
replace.csv =
switchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
G92 E0
G1 E-36 F5000
G92 E0
T{extruder}
G1 X{new_x} Y{new_y} Z{new_z} F{travel_speed}
G1 E36 F5000
G92 E0